Category : Announcements
The St. Albert’s College, Ernakulam invites tenders (technical and financial bids in separate envelopes) for supply and installation of following equipments: (1) Rotary Evaporator (1 no.) (2) Networking (3) Desktop Tiny/Mac Mini Computers- 70 Nos – at St.Albert’s College , Kochi(Kerala). Tenders in sealed envelopes along with the EMDs shall reach the Principal at above address on or before 6th February 2015.
The details of specifications/requirements for the equipment/instruments, terms and conditions for tender, etc can be seen / downloaded from the St. Albert’s College website www.alberts.ac.in
(1) Rotary evaporator
Digital display for rotation speed and heating bath temperature
Rotation speed: 20 to 280 rpm
Heating bath volume: 4 or 5 L
Heating bath temperature range: rt to 180 oC
Chemical resistant diaphragm pump
Ultimate vacuum < 8 mbar
Capable for distilling solvents with high b.p.
Manual vacuum controller and accessories
Temperature range -5 oC to rt
Volume capacity: 3 L
|Wifi Access Points (poe – with concurrent access) with certification and warranty
The access points should support continuous connection when the units switch from the prescribed area of one AP to another
|Cabling to the Access Points|
|Wireless Controller and configuration
Controller Bases and stand alone
|cat 6 cabling in the computer lab|
Preferred brands (in random order): D-link, Netgear, HP, Cisco Access points
Preferred brands (in random order): D-link, Molex cables
i5 computers with protection (hardware lock).
4 GB, 500 GB stand-alone systems.
Green Computing – low power consumption
The CPUs should be mounted on the back of the monitor / clamped to the desk (for mac minis) with least power consumption.
Preferred brands (in random order): Dell, HP, Lenovo, Apple
General Terms and Conditions
|1||Model and year of introduction of the instrument||Shall be mentioned in the tender along with original brochures /catalogue. Though the specifications given are of basic and general in nature, preference will be given for selection of higher- end versions. Therefore, bidders are advised to quote for different models.|
|2||Place of installation||At St. Albert’s College, Ernakulam|
|4||Delivery and installation of equipment:||(i) The confirmation of acceptance of purchase order by the supplier shall be given with in 7(seven) days from the date of issue of purchase order.(ii) Delivery and installation to be completed within 8 weeks from the date of opening of L/C.(iii) Short shipment and part shipment are not allowed.
|5||Price||(i) The price shall be quoted in foreign and Indian currencies, indicating break-up for the equipment and accessory instruments, details of import duty/ tax as applicable and other over-heads. The price shall be inclusive of all costs of freight, insurance, transportation, delivery (door delivery) and installation & commissioning at the respective laboratory.(iii) St. Albert’s college reserves the right to accept or reject any offer at its discretion.|
|6||Mode of payment||(i) By Letter of Credit payable in foreign or Indian currency (to be specified): 80% of payment on shipment against L/C documents.
10% of payment after installation, commissioning and training by the supplier to the satisfaction of St Albert’s college.
In case of indigenous equipment, 90% of the payment in rupee terms shall be released against satisfactory installation, commissioning and training of the equipment in the respective labs.
Balance 10% of payment against furnishing of irrevocable bank guarantee by the supplier for equivalent Indian Rupees (issued by a nationalized bank) as performance guarantee for Two from the date of successful installation and commissioning of the instrument/s.
(ii) In case the supplier cannot provide the bank guarantee as above, the 10% of payment (in equivalent Indian Rupees) shall be retained with St. Albert’s College and released on the expiry of Two after the successful installation and commissioning of the instrument/s.
|7||Warranty||(i) Two years from the date of completion of installation for the complete system including replacement of instruments and parts, spares, accessories and labour charges.(ii) Complete set of spares and consumables as stand by shall be provided/made available along with the equipment or from time to time during the period of warranty.(iii) The repair/servicing and periodic IPV (Instrument Performance Verification) of the equipment with traceable standards have to be carried out by the manufacturer/supplier free of cost during the entire warranty period, or extended warranty period irrespective of any number of repairs / services.
(iv) Definite time schedule for servicing of equipment, time required for attending break-downs, etc shall be indicated in the terms & conditions for warranty and AMC.
(vi) Shall provide good after sale service/technical support capable of attending on short notice at places where the equipment is installed. At least 2 preventive maintenance visits and unlimited breakdown calls by the service/application support engineer during the warranty period, every year.
(vii) The manufacturer / supplier shall give a warranty certificate as per the format attached in the tender Document (Annex I).
|8||After sales service||(i) Shall provide for annual maintenance contract / after sale service contract after the warranty period.(ii) The cost/rate and the terms and conditions for AMC and IPV for three years, after the warranty period (3rd , 4th & 5th years) have to be specified.(iii) The payment terms for the AMC shall be as per the Rule 159 of GFR 2005(Govt. of India) and amendments there to.
(iv) Definite time schedule for servicing of equipment, time required for attending break-downs, etc shall be indicated in the terms & conditions for AMC.
(v) St Albert’s college reserves the right to impose penalty @ `. 2000/- per day for the delay or other lapses of the manufacturer/supplier/ service provider in rectification of the break-downs beyond 3 working days, during the AMC period.
|9||Training of personnel||(i) Basic training for a period not less than two weeks after installation of the equipment to our technicalpersonnel of the concerned laboratory.(ii) Trouble shooting training as and when required.|
|10||Experience||The supplier shall have experience of at least 20 installations and operation of the equipment in India, including the model quoted.|
|11||Details of EMD||1% of the amount for the total number of equipment (the highest valued model quoted), by way of Demand Draft or Cheque (payable at par) drawn on any of the Nationalized Bank in favour of Principal, St. Albert’s College, Kochi.|
|12||Period of validity of the offer/tender||90 days.|
|13||Specification sheets||Detailed specification sheet(s) highlighting all the technical and other specifications must be attached|
|14||Users List||Complete list of users in India for the equipment (inclusive of the quoted model) along with certificates/testimonials from the customers shall be enclosed.|
|15||Instrument Performance Verification (IPV) (IQ, OQ & PQ)||To be done free of cost with traceable standards for the first 2 years (on installation, every year, after break-downs and as when repair(s) are carried out).|
|16||Cost of tender documents||The tender document may be downloaded from St. Albert’s college website and the amount of Rs. 1000/- (Rupees One Thousand only) may be paid towards the tender document fee by Demand draft or Multicity cheque in favour of Principal, St. Albert’s College, Kochi.|
|17||Last date and time of receipt of tender||16.00 hrs on 6. 2. 2015. Tenders received late for any reason whatsoever, shall not be entertained. St. Albert’s College has the right to reject any or all tenders without assigning any reason.|
|18||Submission of tender||The tender shall be duly signed, sealed, super-scribed as “Tender for supply of ……………” and submitted to: St. Albert’s College, Ernakulam, Banerji Road, Kochi 682 018, India|
|19||Installation Check out specification.||Shall be provided by the supplier.|
The technical presentation on instruments / equipment is to be made at St. Albert’s College , Kochi after opening the technical bids (the date shall be informed later). The price bids (of two bid tender system) shall be opened only after technical evaluation of the technical bids. Those who qualify technically only will be considered for opening of financial bids.
Earnest money deposits (EMD) for the amount of 1% of the price/value (based on total number of equipment quoted) in the form of demand draft / cheque (payable at par) drawn in the name of Principal, St. Albert’s College , Kochi shall be submitted along with the tenders. The firm registered with DGS&D / NSIC as manufacturer for the supply of the same category of item for which the party is submitting quotation will be exempted from submission of EMD. Exempted parties will have to give proof of registration along with their quotation. EMD of the unsuccessful bidders shall be refunded at the earliest but latest within 30 days after finalization of the purchase of concerned item.
The Principal, St. Albert’s College reserves the right to reject the bids or to cancel/postpone the procurements without assigning any reason whatsoever.
We Warrant that all the machines, equipment and accessories supplied by us under the Purchase Order bearing No._________ Dated _______ , shall be brand new, free from all defects – patent or latent and faults in materials, workmanship and manufacture and shall be of the highest grade and quality and consistent with the established and generally accepted standards for material of the type ordered and shall be in full conformity with the specifications, drawing or samples and shall operate properly. We shall be fully responsible for its efficient performance. This Warranty shall survive irrespective of any payment or acceptance of the goods but shall expire after (except in respect of complaints and all manufacturing defects of which we have been notified prior to such date) Two years after the installation and acceptance of equipment by St. Albert’s College, Ernakulam.
The obligations under the Warranty expressed above shall include all costs relating to labour, spares, maintenance (preventive and unscheduled/breakdown service) and transport charges from site to the manufacturers work place and back and free repair/adjustment or replacement at site. This Warranty shall bind us, our assigns and successors.
Date : Signature of Bidder
Name & Designation